Adhesive: lamination
When bonding YUPO and paper*1
Processing target
Wet lamination*2
Compatible adhesives
<EVA emulsion>
BX-646X (Touritsu Kasei)
When bonding YUPO and paper*1
Processing target
Wet lamination*2
Compatible adhesives
<Acrylic emulsion>
PZ-905 (Saiden Chemical)
When bonding YUPO and film
Processing target
Dry lamination*3
YUPO/YUPO
Compatible adhesives
<Polyether (two-component)>*4
TM329/CAT8B (Toyo Morton)
When bonding YUPO and film
Processing target
Dry lamination*3
YUPO/PET
Compatible adhesives
<Polyester (two-component)>
TM595/CAT56 (Toyo Morton)
When bonding YUPO and film
Processing target
Dry lamination*3
YUPO/aluminum foil
Compatible adhesives
<Polyester (two-component)>
TM595/CAT56 (Toyo Morton)
When bonding YUPO and film
Processing target
YUPO/plastic container
Heat seal coat
Compatible adhesives
<LDPE>
When bonding YUPO and film
Processing target
YUPO/plastic container
Sand lamination*5
Compatible adhesives
<LDPE>
Print lamination*6
(automatic application)
Processing target
YUPO printed material/OPP
Compatible adhesives
<EVA (two-component)>
BLS-PG17/CAT100 (Toyo Morton)
Print lamination*6
(automatic application)
Processing target
YUPO printed material/OPP
Compatible adhesives
<Acrylic emulsion (one-component)>
EA-G31 (Toyo Morton)
Print lamination*6
(automatic application)
Processing target
YUPO printed material/OPP
Compatible adhesives
<Acrylic emulsion (two-component)>
EA-G34/CAT-EP8 (Toyo Morton)
AP368A/B (Japan Coating Resin)
Polisuchikku main agent EM-572/Hardener EM-545K, Polisuchikku main agent EM-575/Hardener EM-545K (Arakawa Toryo Kogyo)
Print lamination*6
(automatic application)
Processing target
YUPO printed material/Thermal adhesive resin coated OPP, PET
Compatible adhesives
<Print laminating film>
Lamitack (J-Film)
Print lamination*6
(automatic application)
Processing target
YUPO printed material/PVC
Large hanging banner
For thin items
Compatible adhesives
<Polyester (two-component)>
BLS-PC21/CAT100 (Toyo Morton)
Print lamination*6
(automatic application)
Processing target
YUPO printed material/PVC
Large hanging banner
For thick items
Compatible adhesives
<Polyester (two-component)>
BLS-PC50/CAT100 (Toyo Morton)
Heat press lamination*7
Processing target
YUPO printed material/PVC*8
(Underlay, cards, mouse pads, etc.)
Compatible adhesives
<Acrylic emulsion>
BLS-3082/CAT100 (Toyo Morton)
Heat press lamination*7
Processing target
YUPO printed material/PP*8
Compatible adhesives
<Polyester (two-component)>
BLS-3082/CAT100 (Toyo Morton)
Dry lamination
Processing target
YUPO/OPP, CPP
Compatible adhesives
<Acrylic copolymer (two-component)>
AP368A/B (Japan Coating Resin)
- *1 Bonding using a laminator
Be aware that there is a significant risk of curling after lamination. - *2 We recommend dry lamination for thin paper.
- *3 Non-absorbent materials and laminate (roll to roll)
To prevent curling, set the tension, dryer and temperature as low as possible. - *4 If heat- and water-resistant lamination is necessary, consult with the adhesive manufacturer.
- *5 If a strong bond is necessary, apply an undercoat. Curling may occur due to contraction upon cooling, so roll in the reverse direction.
- *6 Bonding of sheets and rolls
Keep the film tension low to prevent curling. After lamination, turn the film side upwards and roll, and cut the sheet after rectifying the curl. - *7 Sheet to sheet bonding
- *8Apply a coat to the PVC or PP side. When coating the YUPO side, the ink may run if it is insufficiently dried.